Harley Davidson FXLRS & FXLRST cable fitment
When customizing your Harley-Davidson Low Rider S (FXLRS) or Low Rider ST (FXLRST) hand controls, getting the right cable fitments is crucial to achieve propper installation. Whether you're upgrading to taller risers, swapping out handlebars, or fine-tuning your bike's ergonomics, the proper cable lengths can make or break your setup.
From the upper clutch cable and upper brake line to the various harnesses for controls, speedometer and throttle, each cable must be precisely matched to your chosen riser height and bar model. This guide will walk you through the essentials of cable fitment, ensuring that every connection on your Low Rider S & ST is just right, so you can focus on the ride, not the setup.
All information provided below is for reference only and may differ based on your specific setup. Original Garage Moto is not responsible for any cable, brake line, or harness fitment issues that may arise. It's important to note that the recommendations and measurements we discuss are intended for builds using stock cables.
If your Low Rider S or Low Rider ST has been modified or equipped with aftermarket components, you may need to make further adjustments to ensure proper fitment. Always double-check your measurements and consider consulting a professional for custom builds.
2020 to present Softail Low Rider S & ST Cable Fitment
| Risers | Bar | Overall Height | Upper Clutch Cable (Quick Connect) |
Upper Brake Line | Control Harness | Speedometer Harness | TGS Harness |
|---|---|---|---|---|---|---|---|
| OEM | OEM | 10" | - | - | - | - | - |
| 6.5" | ODI Podium Moto Bar | 10.5" | OEM | OEM | OEM if the controls connector caddy located in the frame is removed | OEM | OEM |
| ODI Podium Tracker Bar | 8" | OEM | OEM | OEM | OEM | OEM | |
| 8.5" | ODI Podium Moto Bar | 12.5" | +2" | +2" | +4" |
2020-2021 FXLRS: OEM 2022 to present FXLRS: +4" 2022 to present FXLRST: OG 18+ M8 Softail Digital Gauge Extended Harness |
+4" |
| ODI Podium Tracker Bar | 10" | OEM | OEM | OEM if the controls connector caddy located in the frame is removed |
2020-2021 FXLRS: OEM 2022 to present FXLRS: +4" 2022 to present FXLRST: OG 18+ M8 Softail Digital Gauge Extended Harness |
OEM | |
| 10.5" | ODI Podium Moto Bar | 14.5" | +4" | +4" | +4" |
2020-2021 FXLRS: OEM 2022 to present FXLRS: +4" 2022 to present FXLRST: OG 18+ M8 Softail Digital Gauge Extended Harness |
+4" |
| ODI Podium Tracker Bar | 12" | +2" | +2" | +4" |
2020-2021 FXLRS: OEM 2022 to present FXLRS: +4" 2022 to present FXLRST: OG 18+ M8 Softail Digital Gauge Extended Harness |
+4" |
Cable References
| Clutch Cable | +2" | Manufacturer: | Magnum Shielding |
|---|---|---|---|
| P/N: | 42342HE | ||
| +4" | Manufacturer: | Magnum Shielding | |
| P/N: | 42344HE | ||
| Brake Line (ABS) | +2" | Manufacturer: | Magnum Shielding |
| P/N: | AS478124 + AS47026 | ||
| +4" | Manufacturer: | Magnum Shielding | |
| P/N: | AS478126 + AS47026 | ||
| Control Harness | +4" | Manufacturer: | Guerilla Cables |
| P/N: | 24020-1106 (6") | ||
| Speedo Meter Harness | +4" | Manufacturer: | Guerilla Cables |
| P/N: | 24080-1026 (22") | ||
| TGS Harness | +4" | Manufacturer: | Guerilla Cables |
| P/N: | 24025-1606 (6") |
5 comments
Anthony
I have a 2020 low rider s, looking to get the 10.5 inch risers with the 1.5 inch pull back. Which cables would I need
Original Garage Moto
Hey Raudel, thanks for reaching out!
When using the OG Pullback Plate on your 2023 Low Rider S with 8.5" straight risers (whether you go with the moto bar or stock bar), we recommend the following extensions to ensure everything fits perfectly:
+2" clutch cable
+2" brake line
+4" control harness
+4" TGS harness
Give us a call or email us if you need any further assistance!
+1 866-835-3402
info@originalgaragemoto.com
Raudel
I have a 2023 Low Rider S with your OG pullback plate. I’m looking into the 8.5 straight riders with either the moto bar or stock bar. Is it recommended to follow the chart or does the pullback plate change any measurements? Thanks in advance!
Original Garage Moto
Hey there Aaron,
Let’s take things apart and begin with your 2024 Low Rider.
For an 8.5" Risers with an OEM Bar, you will need these extensions:
Upper Clutch Cable(Quick Connect): +2"
Upper Brake Line: +2"
Control Harness: +4"
Speedometer Harness: +4"
TGS Harness: +4
Now, for a 2024 Low Rider ST.
For an 8.5" Risers with an OEM Bar, you will need these extensions:
Upper Clutch Cable(Quick Connect): 2"
Upper Brake Line: +2"
Control Harness: +4"
Speedometer Harness: OG 18 M8 Softail Digital Gauge Extended Harness
TGS Harness: +4
Aaron
I have a 24 low rider and also a 24 low rider st , looking to use stock bars with 8.5 riser w/pullback. What extensions will I need to complete install?